STM32h7 接收各种can id情况下滤波器的配置

1、接收所有数据

/* 此处id2都为0，不进行id校验，接收所有数据*/
static void CAN_Filter_Config(void){FDCAN_FilterTypeDef sFilterConfig1;/* Configure Rx filter */sFilterConfig1.IdType = FDCAN_STANDARD_ID;sFilterConfig1.FilterIndex = 0;sFilterConfig1.FilterType = FDCAN_FILTER_MASK;sFilterConfig1.FilterConfig = FDCAN_FILTER_TO_RXFIFO0;sFilterConfig1.FilterID1 = 0x111;sFilterConfig1.FilterID2 = 0x000; /* For acceptance, MessageID and FilterID1 must match exactly */HAL_FDCAN_ConfigFilter(&hfdcan1, &sFilterConfig1);}

2、只接受单个id

/*此处只接收ID为“123”的can数据 */static void CAN_Filter_Config(void){FDCAN_FilterTypeDef sFilterConfig1;/* Configure Rx filter */sFilterConfig1.IdType = FDCAN_STANDARD_ID;sFilterConfig1.FilterIndex = 0;sFilterConfig1.FilterType = FDCAN_FILTER_MASK;sFilterConfig1.FilterConfig = FDCAN_FILTER_TO_RXFIFO0;sFilterConfig1.FilterID1 = 0x123;sFilterConfig1.FilterID2 = 0x7FF; /* For acceptance, MessageID and FilterID1 must match exactly */HAL_FDCAN_ConfigFilter(&hfdcan1, &sFilterConfig1);}

3、接收两个id

/*此处接收ID为“123”及“456”的can数据 */static void CAN_Filter_Config(void){FDCAN_FilterTypeDef sFilterConfig1;/* Configure Rx filter */sFilterConfig1.IdType = FDCAN_STANDARD_ID;sFilterConfig1.FilterIndex = 0;sFilterConfig1.FilterType = FDCAN_FILTER_DUAL;sFilterConfig1.FilterConfig = FDCAN_FILTER_TO_RXFIFO0;sFilterConfig1.FilterID1 = 0x123;sFilterConfig1.FilterID2 = 0x456; /* For acceptance, MessageID and FilterID1 must match exactly */HAL_FDCAN_ConfigFilter(&hfdcan1, &sFilterConfig1);}

4、接收一定范围的id

/*此处接收ID在“111”~“666”之间的can数据 */static void CAN_Filter_Config(void){FDCAN_FilterTypeDef sFilterConfig1;/* Configure Rx filter */sFilterConfig1.IdType = FDCAN_STANDARD_ID;sFilterConfig1.FilterIndex = 0;sFilterConfig1.FilterType = FDCAN_FILTER_RANGE;sFilterConfig1.FilterConfig = FDCAN_FILTER_TO_RXFIFO0;sFilterConfig1.FilterID1 = 0x111;sFilterConfig1.FilterID2 = 0x666; /* For acceptance, MessageID and FilterID1 must match exactly */HAL_FDCAN_ConfigFilter(&hfdcan1, &sFilterConfig1);}

5、接收特定规则的id

/*FilterType 类型配置为 FDCAN_FILTER_MASK 表示经典的位屏蔽过滤。FilterID1 = filter 表示 ID。FilterID2 = mask 表示 ID 屏蔽位，mask 每个 bit 含义：0: 表示 FilterID1 相应 bit 不关心，该位不用于比较。1: 表示 FilterID1 相应 bit 必须匹配，即接收到的 ID 位必须与 FilterID1 的相应位一致。我们这里 FilterID1 = 0x200，bit “1 0 0 0 0 0 0 0 0 0”FilterID2 = 0x300 ，bit “1 1 0 0 0 0 0 0 0 0”表示接收Id bit9必须为1，bit8必须为0，其他bit0~bit7不受限制。也就是接收0x200~0x300之间的数据*/static void CAN_Filter_Config(void){FDCAN_FilterTypeDef sFilterConfig1;/* Configure Rx filter */sFilterConfig1.IdType = FDCAN_STANDARD_ID;sFilterConfig1.FilterIndex = 0;sFilterConfig1.FilterType = FDCAN_FILTER_MASK;sFilterConfig1.FilterConfig = FDCAN_FILTER_TO_RXFIFO0;sFilterConfig1.FilterID1 = 0x200;sFilterConfig1.FilterID2 = 0x300; /* For acceptance, MessageID and FilterID1 must match exactly */HAL_FDCAN_ConfigFilter(&hfdcan1, &sFilterConfig1);}