当前位置： 首页 > news >正文

Stm32_标准库_18_串口蓝牙模块_手机与蓝牙模块通信_控制LED灯亮灭

news 2025/12/28 2:34:36

通过输入LED_ON和LED_OFF分别控制LED灯的亮与灭

接线：

LED的正极接正电，负极接GPIOA_Pin1

蓝牙模块TXD接GPIOA_Pin3,VCC接正电，GND接负电

注意：USART2是APB1外设，汉字占用字节数是字符的两倍

使用：

手机向蓝牙传输"LED_ON",LED灯亮，反之传输“LED_OFF”则LED灯熄灭

代码：

main函数：

#include "stm32f10x.h"                  // Device header
#include "Delay.h"
#include "OLED.h"
#include "Serial.h"
#include "LED.h"char *News;void OledShow(void){OLED_ShowCHINESE(1,1,8);OLED_ShowCHINESE(1,2,9);OLED_ShowString(1, 5, ":LED_ON");OLED_ShowCHINESE(2,1,8);OLED_ShowCHINESE(2,2,10);OLED_ShowString(2, 5, ":LED_OFF");OLED_ShowCHINESE(3,1,4);OLED_ShowCHINESE(3,2,5);OLED_ShowString(3, 5, ":NONEL");OLED_ShowCHINESE(4,1,6);OLED_ShowCHINESE(4,2,7);OLED_ShowString(4, 5, ":NONE");
}int main(void){OLED_Init();LED_Init();Serial_Init();OledShow();while (1){if(Serial_GetRxFlag() == 1){News = Serial_returnNews();Serial_drlContrl(News);Serial_StateRecovery(News);}}
}

LED.c 和 LED.h

#include "stm32f10x.h"                  // Device headervoid LED_Init(void)
{RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);GPIO_InitTypeDef GPIO_InitStructure;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOA, &GPIO_InitStructure);GPIO_SetBits(GPIOA, GPIO_Pin_1);
}void LED1_ON(void)
{GPIO_ResetBits(GPIOA, GPIO_Pin_1);
}void LED1_OFF(void)
{GPIO_SetBits(GPIOA, GPIO_Pin_1);
}
#ifndef __LED_H
#define __LED_Hvoid LED_Init(void);
void LED1_ON(void);
void LED1_OFF(void);#endif

OLED.c扩充函数及OLED.h

void OLED_ShowCHINESE(uint8_t Line, uint8_t Column, uint8_t Num)
{uint8_t i;uint8_t wide = 16;//字宽OLED_SetCursor(( Line - 1 ) * 2, ( Column - 1 )* wide);		//参数1:把光标设置在第几页. 参数2:把光标设置在第几列for (i = 0; i < wide; i++){OLED_WriteData(OLED_F10x16[Num][i]);			//显示上半部分内容}OLED_SetCursor(( Line - 1 ) * 2 + 1,( Column - 1) * wide);		for (i = 0; i < wide ; i++){ OLED_WriteData(OLED_F10x16[Num][i+wide]);		//显示下半部分内容}}/* 直接用清屏函数整体刷新会导致OLED画面不连贯清除行函数：保留本行字符串，清除本行剩余部分row：清除的具体行begin:开始清除的位置end:清除结束的位置
*/void OLED_ClearLocation(uint8_t row, uint8_t begin, uint8_t end)
{  uint8_t i, j;for (j = row * 2 - 2; j < row * 2; j++){OLED_SetCursor(j, begin * 8);for(i = begin * 8; i < end * 8; i ++){OLED_WriteData(0x00);}}
}

#ifndef __OLED_H
#define __OLED_H
#include "stm32f10x.h"                  // Device headervoid OLED_Init(void);
void OLED_Clear(void);
void OLED_ClearLocation(uint8_t row, uint8_t begin, uint8_t end);
void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char);
void OLED_ShowString(uint8_t Line, uint8_t Column, char *String);
void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length);
void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length);
void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length);
void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length);
uint8_t OLED_GetNumLength(uint16_t num);
void OLED_ShowCHINESE(uint8_t Line, uint8_t Column, uint8_t Num);
#endif

OLED_Font.h

#ifndef __OLED_FONT_H
#define __OLED_FONT_H
#include "stm32f10x.h"                  // Device header/*OLED字模库，宽8像素，高16像素*/
const uint8_t OLED_F8x16[][16]=
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//  00x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 10x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 20x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 30x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 40xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 50x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 60x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 70x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 80x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 90x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 100x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 110x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 120x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 130x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 140x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 150x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 160x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 170x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 180x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 190x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 200x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 210x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 220x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 230x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 240x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 250x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 260x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 270x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 280x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 290x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 300x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 310xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 320x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 330x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 340xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 350x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 360x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 370x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 380xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 390x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 400x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 410x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 420x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 430x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 440x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 450x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 460xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 470x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 480xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 490x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 500x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 510x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 520x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 530x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 540xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 550x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 560x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 570x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 580x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 590x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 600x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 610x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 620x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 630x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 640x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 650x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 660x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 670x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 680x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 690x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 700x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 710x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 720x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 730x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 740x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 750x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 760x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 770x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 780x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 790x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 800x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 810x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 820x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 830x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 840x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 850x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 860x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 870x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 880x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 890x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 900x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 910x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 920x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 930x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};const uint8_t OLED_F10x16[][32] ={0x10,0x60,0x02,0x8C,0x00,0x00,0xFE,0x92,0x92,0x92,0x92,0x92,0xFE,0x00,0x00,0x00,
0x04,0x04,0x7E,0x01,0x40,0x7E,0x42,0x42,0x7E,0x42,0x7E,0x42,0x42,0x7E,0x40,0x00,/*"温",0*/0x00,0x00,0xFC,0x24,0x24,0x24,0xFC,0x25,0x26,0x24,0xFC,0x24,0x24,0x24,0x04,0x00,
0x40,0x30,0x8F,0x80,0x84,0x4C,0x55,0x25,0x25,0x25,0x55,0x4C,0x80,0x80,0x80,0x00,/*"度",1*/0x40,0x40,0x42,0x44,0x58,0xC0,0x40,0x7F,0x40,0xC0,0x50,0x48,0x46,0x40,0x40,0x00,
0x80,0x80,0x40,0x20,0x18,0x07,0x00,0x00,0x00,0x3F,0x40,0x40,0x40,0x40,0x78,0x00,/*光,2*/0x00,0xFE,0x42,0x42,0x42,0xFE,0x00,0x42,0xA2,0x9E,0x82,0xA2,0xC2,0xBE,0x00,0x00,
0x80,0x6F,0x08,0x08,0x28,0xCF,0x00,0x00,0x2F,0xC8,0x08,0x08,0x28,0xCF,0x00,0x00,/*"照",3*/0x00,0x08,0x30,0x00,0xFF,0x20,0x20,0x20,0x20,0xFF,0x20,0x20,0x22,0x2C,0x20,0x00,
0x04,0x04,0x02,0x01,0xFF,0x80,0x40,0x30,0x0E,0x01,0x06,0x18,0x20,0x40,0x80,0x00,/*"状",4*/0x00,0x04,0x84,0x84,0x44,0x24,0x54,0x8F,0x14,0x24,0x44,0x84,0x84,0x04,0x00,0x00,
0x41,0x39,0x00,0x00,0x3C,0x40,0x40,0x42,0x4C,0x40,0x40,0x70,0x04,0x09,0x31,0x00,/*"态",5*/0x10,0x10,0x10,0xFF,0x10,0x50,0x44,0x54,0x65,0xC6,0x44,0x64,0x54,0x44,0x40,0x00,
0x04,0x44,0x82,0x7F,0x01,0x82,0x82,0x4A,0x56,0x23,0x22,0x52,0x4E,0x82,0x02,0x00,/*"接",6*/0x00,0xFC,0x00,0x00,0xFF,0x00,0x40,0x20,0xD8,0x17,0x10,0x10,0xF0,0x10,0x10,0x00,
0x00,0x0F,0x04,0x02,0xFF,0x00,0x80,0x40,0x21,0x16,0x08,0x16,0x21,0x40,0x80,0x00,/*"收",7*/0x80,0x70,0x00,0xFF,0x20,0x10,0x04,0x04,0x04,0x04,0xFC,0x04,0x04,0x04,0x04,0x00,
0x80,0x60,0x18,0x07,0x08,0x30,0x00,0x00,0x40,0x80,0x7F,0x00,0x00,0x00,0x00,0x00,/*"灯",8*/0x00,0x04,0x04,0x74,0x54,0x54,0x55,0x56,0x54,0x54,0x54,0x74,0x04,0x04,0x00,0x00,
0x84,0x83,0x41,0x21,0x1D,0x05,0x05,0x05,0x05,0x05,0x7D,0x81,0x81,0x85,0xE3,0x00,/*"亮",9*/0x02,0x02,0x82,0x72,0x02,0x02,0x02,0xFE,0x02,0x02,0x82,0x42,0x32,0x02,0x02,0x00,
0x80,0x81,0x40,0x20,0x10,0x0C,0x03,0x00,0x03,0x0C,0x10,0x20,0x40,0x80,0x80,0x00,/*"灭",10*/};
#endif

Serial.c及Serial.h

#include "stm32f10x.h"                  // Device header
#include <stdio.h>
#include <stdarg.h>
#include "Delay.h"
#include <stdlib.h>
#include "OLED.h"
#include <String.h>
#include "LED.h"uint8_t Serial_RxData;//存数据
uint8_t Serial_RxFlag;//标志位
GPIO_InitTypeDef GPIO_InitStructu;//GPIO
USART_InitTypeDef USART_InitStructure;//串口
NVIC_InitTypeDef NVIC_InitStructur;//中断
char news[100] = "";//存数据
uint8_t I = 0;
uint8_t flagDate = 0;//标志是否传入日期数据
uint8_t flagTime = 0;//标志是否传入时间数据void Serial_Init(void)
{RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);GPIO_InitStructu.GPIO_Mode = GPIO_Mode_IPU;//输入上拉GPIO_InitStructu.GPIO_Pin = GPIO_Pin_3;GPIO_InitStructu.GPIO_Speed = GPIO_Speed_50MHz;GPIO_Init(GPIOA, &GPIO_InitStructu);USART_InitStructure.USART_BaudRate = 9600;USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;USART_InitStructure.USART_Mode = USART_Mode_Rx;USART_InitStructure.USART_Parity = USART_Parity_No;USART_InitStructure.USART_StopBits = USART_StopBits_1;USART_InitStructure.USART_WordLength = USART_WordLength_8b;USART_Init(USART2, &USART_InitStructure);USART_ITConfig(USART2, USART_IT_RXNE, ENABLE);NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);//通道NVIC_InitStructur.NVIC_IRQChannel = USART2_IRQn;//中断通道NVIC_InitStructur.NVIC_IRQChannelCmd = ENABLE;NVIC_InitStructur.NVIC_IRQChannelPreemptionPriority = 3;NVIC_InitStructur.NVIC_IRQChannelSubPriority = 1;NVIC_Init(&NVIC_InitStructur);USART_Cmd(USART2, ENABLE);
}uint8_t Serial_GetRxFlag(void)//读取标志位后自动青除
{if (Serial_RxFlag == 1){Serial_RxFlag = 0;return 1;}return 0;
}uint8_t Serial_GetFlagDate(void)//读取标志位后自动青除
{if (flagDate == 1){flagDate = 0;return 1;}return 0;
}uint8_t Serial_GetFlagTime(void)//读取标志位后自动青除
{if (flagTime == 1){flagTime = 0;return 1;}return 0;
}void Serial_GetRxFlag_SET(void){Serial_RxFlag = 1;
}char * Serial_returnNews(void){//返还一个数组char * array;uint8_t i = 0;array = (char *) malloc(sizeof(char) * 100);Delay_ms(300);//等待数据传输完while(i < I){if(news[i] == '/') flagDate = 1;if(news[i] == ':') flagTime = 1;array[i] = news[i];i ++;}return array;
}void Serial_RESETI(void){//初始化II = 0;
}uint8_t Serial_GetI(void){//返回Ireturn I;
}void USART2_IRQHandler(void)//中断函数
{if (USART_GetITStatus(USART2, USART_IT_RXNE) == SET){news[I] = USART_ReceiveData(USART2);//读数据Serial_RxFlag = 1;//至标志位为有数据I ++;USART_ClearITPendingBit(USART2, USART_IT_RXNE);}
}void Serial_StateRecovery(char *News){Serial_RESETI();//I至0Serial_GetRxFlag();//制零否者if循环将会被执行两次free(News);//释放空间必须释放否者发生地址紊乱，直接卡机
}void Serial_drlContrl(char * News){News[I] = '\0';if(strcmp(News, "LED_ON") == 0){LED1_ON();OLED_ShowString(3, 6, "RIGHT");}else if(strcmp(News, "LED_OFF") == 0){LED1_OFF();OLED_ShowString(3, 6, "RIGHT");}else{ 		 OLED_ShowString(3, 6, "ERROR");}OLED_ClearLocation(4, 6, 16);OLED_ShowString(4, 6, News);Delay_ms(2000);OLED_ShowString(3, 6, "NONEL");}

#ifndef __SERIAL_H
#define __SERIAL_H
#include "stm32f10x.h"  
#include <stdio.h>void Serial_Init(void);
uint8_t Serial_GetRxFlag(void);
uint8_t Serial_GetRxData(void);
void Serial_GetRxFlag_SET(void);
char * Serial_returnNews(void);
void Serial_RESETI(void);
uint8_t Serial_GetI(void);
uint8_t Serial_GetFlagTime(void);
uint8_t Serial_GetFlagDate(void);
void Serial_StateRecovery(char *News);
void Serial_drlContrl(char * News);#endif

相关文章：

Stm32_标准库_18_串口蓝牙模块_手机与蓝牙模块通信_控制LED灯亮灭

通过输入LED_ON和LED_OFF分别控制LED灯的亮与灭 接线&#xff1a; LED的正极接正电&#xff0c;负极接GPIOA_Pin1 蓝牙模块TXD接GPIOA_Pin3,VCC接正电&#xff0c;GND接负电 注意&#xff1a;USART2是APB1外设&#xff0c;汉字占用字节数是字符的两倍 使用&#xff1a; 手…...

编程日记 2023/11/14 15:07:47

低代码与传统开发：综合比较

近年来&#xff0c;低代码开发作为软件开发的趋势获得了显着的发展势头。根据 MarketsandMarkets 的数据&#xff0c;低代码开发市场预计将实现 28.1% 的大幅增长率&#xff0c;到 2025 年价值将达到 455 亿美元。这一显着增长表明了各行业和企业对低代码平台的需求和采用不断增…...

编程日记 2023/11/14 15:06:46

pyqt环境搭建

创建虚拟环境 # 用管理员身份运行 conda create --prefixE:\Python\envs\pyqt5stu python3.6 # 激活虚拟环境 conda activate E:\Python\envs\pyqt5stu # 退出虚拟环境 conda deactivate安装包 pip install PyQt5 -i https://pypi.douban.com/simple pip install PyQt5-tools…...

编程日记 2023/11/14 15:05:44

JavaScript数据类型和存储区别

目录 一、原始数据类型 二、引用数据类型 三、存储区别 四、常见错误 JavaScript是一种动态类型语言&#xff0c;这意味着变量可以在程序执行过程中改变其数据类型。了解JavaScript中的数据类型和它们的存储方式对于编写高效和可维护的代码至关重要。 在JavaScript中&…...

编程日记 2023/11/14 15:04:43

Java学习笔记（七）——面向对象编程（中级）

一、IDEA &#xff08;一&#xff09;常用的快捷键 &#xff08;二&#xff09;模版/自定义模版 二、包 &#xff08;一&#xff09;包的命名 &#xff08;二&#xff09;常用的包 &#xff08;三&#xff09;如何引入&#xff08;导入&#xff09;包 &#xff08;四&am…...

编程日记 2023/11/14 15:03:42

详细推导MOSFET的跨导、小信号模型、输出阻抗、本征增益

目录 前言 什么是跨导 什么是小信号模型 什么是输入阻抗和输出阻抗 什么是MOS管的输出阻抗 什么是MOS管的本征增益 共源极放大电路的输入和输出阻抗 一些其它MOS拓扑电路的增益 负载为恒流源 负载为二极管 前言 相信很多人在学习集成电路领域的时候 都对MOS管的…...

编程日记 2023/11/14 15:02:40

循环2作业

第一题 #include <stdio.h>int main() {int n,f,y,i,j;scanf("%d",&n);for(y0;y<100;y)for(f0;f<100;f)if(200*y2*ff*100y-n){printf("%d.%d",y,f);return 0;}printf("%d No Solution",n);return 0; }第二题 #include<stdi…...

编程日记 2023/11/14 15:01:39

一个车厢号码识别算法（2005年的老程序----ccc）

一个车厢号码识别算法&#xff08;2005年的老程序----ccc&#xff09; 2023-09-18 ccc 程序的识别效果 对图中的车厢号码部分用上下两条线限定分为&#xff0c;然后进行识别。 从上面的识别效果可以看出&#xff0c;识别算法具有一定的鲁棒性&#xff0c;能够适应车厢号码的各…...

编程日记 2023/11/14 15:00:38

「Verilog学习笔记」优先编码器电路①

专栏前言 本专栏的内容主要是记录本人学习Verilog过程中的一些知识点&#xff0c;刷题网站用的是牛客网 timescale 1ns/1ns//优先编码器电路1 //电路的优先顺序是&#xff0c;从9到1&#xff0c;高级到低级 //9个输入端&#xff1a;I端&#xff0c;4个输出端&#xff1a;Y端&am…...

编程日记 2023/11/14 14:59:36

解决企业项目管理难题：痛点分析与实用解决方案探索

在当前竞争激烈的商业环境中&#xff0c;产品力已然成为市场竞争的核心&#xff0c;这背后的驱动力是技术、人才和管理能力的综合体现——研发创新能力。其中&#xff0c;项目管理能力扮演着至关重要的角色&#xff0c;它能最大化地发挥和释放以上三者的优势。因此&#xff0c;…...

编程日记 2023/11/14 14:58:35

Nginx 简介和安装

文章目录 介绍Nginx的优点(1)速度更快、并发更高(2)配置简单&#xff0c;扩展性强(3)高可靠性(4)热部署(5)成本低、BSD许可证 Nginx的功能特性及常用功能基本HTTP服务高级HTTP服务邮件服务Nginx常用的功能模块 Nginx环境准备docker安装乌班图安装Nginx目录结构分析方式一:Nginx…...

编程日记 2023/11/14 14:57:34

idea生成代码（一）：实现java语言的增删改查功能（基于EasyCode插件）支持自定义模板【非常简单】

idea生成代码&#xff08;一&#xff09;&#xff1a;实现java语言的增删改查功能&#xff08;基于EasyCode插件&#xff09;支持自定义模板【非常简单】 idea生成代码&#xff08;二&#xff09;&#xff1a;实现java语言的增删改查功能&#xff08;基于mybatis-plus代码生成器…...

编程日记 2023/11/14 14:55:32

vue预览各种格式图片png jpg tif tiff dcm

// 没有图片展示暂无 有图片&#xff0c;判断格式 png jpg 直接展示 tif tiff需要转化成png展示 dcm需要用到插件 <el-col :span"16"><div style"width:100%;text-align: center;margin-bottom: 10px;">图件预览</div><div style&quo…...

编程日记 2023/11/14 14:54:31

出入库管理系统vue2前端开发服务器地址配置

【精选】vue.config.js 的完整配置&#xff08;超详细&#xff09;_vue.config.js配置_web学生网页设计的博客-CSDN博客 本项目需要修改两处&#xff1a; 1、vue开发服务器地址&#xff1a;config\index.js use strict // Template version: 1.3.1 // see http://vuejs-templa…...

编程日记 2023/11/14 14:53:30

民安智库（第三方满意度调研公司）：助力奢侈品品牌提升客户满意度

在奢侈品行业中&#xff0c;客户满意度是衡量品牌价值和市场竞争力的关键因素。为了准确了解客户的需求和反馈&#xff0c;民安智库&#xff08;北京第三方社会调查评估&#xff09;以其专业的满意度调查方法&#xff0c;受委托对某奢侈品品牌进行全面的客户满意度调查。 此次…...

编程日记 2023/11/14 14:50:27

蓝牙特征值示例1-迈金L308自行车尾灯夜骑智能表情尾灯的

了解商品级蓝牙特征值 1 服务器&#xff08;设备&#xff09;描述 0x02-01-06 05-03-0F180A18 09-FF-FFFF166B001C0101 0A-09-4C3330385F37393937 01设备标识 03服务UUID FF厂商自定义数据(厂家编号&#xff1a;FFFF-166B001C0101) 完整设备名称&#xff1a; L308-7997 2 服…...

编程日记 2023/11/14 14:49:26

Three 笔记

一&#xff1a;常用函数封装 1、实例化three 场景、相机、渲染器 import * as THREE from three;/*** 实例化three 场景、相机、渲染器* param container: dom容器 * param fov: 视野角度 * param near: 相机视锥体近裁截面相对相机的距离 * param far: 相机视锥体远裁截面相…...

编程日记 2023/11/14 14:48:25

Crypto | Affine password 第二届“奇安信”杯网络安全技能竞赛

题目描述&#xff1a; 明文经过仿射函数y3x9加密之后变为JYYHWVPIDCOZ&#xff0c;请对其进行解密&#xff0c;flag的格式为flag{明文的大写形式}。 密文&#xff1a; JYYHWVPIDCOZ解题思路&#xff1a; 1、使用在线网站直接破解或手工计算破解&#xff0c;获得flag。&#xf…...

编程日记 2023/11/14 14:47:24

android使用notification消息通知（工具类封装）

代码直接复制粘贴就可以用了&#xff0c;参数可以更具自己需求添加 private NotificationManager manager;private Notification notification;private static final String NORMAL_CHANNEL_ID "my_notification_normal";private static final String IMPORTANT_CHA…...

编程日记 2023/11/14 14:46:22

PicoDiagnostics (NVH设备软件)-PS软件设置文件类型介绍

作为远程技术指导人员&#xff0c;下面这个功能对你来说可能非常有帮助。 在PicoScope 7 软件的文件保存格式里&#xff0c;通常选择的是<PS 数据文件>类型&#xff0c;容易忽略其他实用的保存文件类型&#xff0c;下面我们介绍<PS设置文件>类型。 PS 数据文件&…...

编程日记 2023/11/14 14:45:21

挑战杯推荐项目

“人工智能”创意赛 - 智能艺术创作助手&#xff1a;借助大模型技术&#xff0c;开发能根据用户输入的主题、风格等要求&#xff0c;生成绘画、音乐、文学作品等多种形式艺术创作灵感或初稿的应用&#xff0c;帮助艺术家和创意爱好者激发创意、提高创作效率。 ​ - 个性化梦境…...

编程新知 2025/11/6 5:46:16

OpenLayers 可视化之热力图

注&#xff1a;当前使用的是 ol 5.3.0 版本&#xff0c;天地图使用的key请到天地图官网申请&#xff0c;并替换为自己的key 热力图&#xff08;Heatmap&#xff09;又叫热点图&#xff0c;是一种通过特殊高亮显示事物密度分布、变化趋势的数据可视化技术。采用颜色的深浅来显示…...

编程新知 2025/12/9 21:15:58

使用VSCode开发Django指南

使用VSCode开发Django指南 一、概述 Django 是一个高级 Python 框架&#xff0c;专为快速、安全和可扩展的 Web 开发而设计。Django 包含对 URL 路由、页面模板和数据处理的丰富支持。 本文将创建一个简单的 Django 应用&#xff0c;其中包含三个使用通用基本模板的页面。在此…...

编程新知 2025/12/25 2:11:21

Golang 面试经典题：map 的 key 可以是什么类型？哪些不可以？

Golang 面试经典题&#xff1a;map 的 key 可以是什么类型&#xff1f;哪些不可以&#xff1f; 在 Golang 的面试中&#xff0c;map 类型的使用是一个常见的考点&#xff0c;其中对 key 类型的合法性 是一道常被提及的基础却很容易被忽视的问题。本文将带你深入理解 Golang 中…...

编程新知 2025/12/20 7:42:02

如何在看板中体现优先级变化

在看板中有效体现优先级变化的关键措施包括&#xff1a;采用颜色或标签标识优先级、设置任务排序规则、使用独立的优先级列或泳道、结合自动化规则同步优先级变化、建立定期的优先级审查流程。其中&#xff0c;设置任务排序规则尤其重要&#xff0c;因为它让看板视觉上直观地体…...

编程新知 2025/12/17 23:21:43

在 Nginx Stream 层“改写”MQTT ngx_stream_mqtt_filter_module

1、为什么要修改 CONNECT 报文&#xff1f; 多租户隔离&#xff1a;自动为接入设备追加租户前缀&#xff0c;后端按 ClientID 拆分队列。零代码鉴权&#xff1a;将入站用户名替换为 OAuth Access-Token&#xff0c;后端 Broker 统一校验。灰度发布&#xff1a;根据 IP/地理位写…...

编程新知 2025/8/1 10:20:23

【ROS】Nav2源码之nav2_behavior_tree-行为树节点列表

1、行为树节点分类 在 Nav2（Navigation2）的行为树框架中，行为树节点插件按照功能分为 Action（动作节点）、Condition（条件节点）、Control（控制节点） 和 Decorator（装饰节点） 四类。 1.1 动作节点 Action 执行具体的机器人操作或任务，直接与硬件、传感器或外部系统…...

编程新知 2025/12/21 5:00:07

Java多线程实现之Thread类深度解析

Java多线程实现之Thread类深度解析 一、多线程基础概念1.1 什么是线程1.2 多线程的优势1.3 Java多线程模型 二、Thread类的基本结构与构造函数2.1 Thread类的继承关系2.2 构造函数 三、创建和启动线程3.1 继承Thread类创建线程3.2 实现Runnable接口创建线程 四、Thread类的核心…...

编程新知 2025/8/28 21:52:02

服务器--宝塔命令

一、宝塔面板安装命令 ⚠️ 必须使用 root 用户 或 sudo 权限执行&#xff01; sudo su - 1. CentOS 系统&#xff1a; yum install -y wget && wget -O install.sh http://download.bt.cn/install/install_6.0.sh && sh install.sh2. Ubuntu / Debian 系统…...

编程新知 2025/10/3 10:56:48

return this；返回的是谁

一个审批系统的示例来演示责任链模式的实现。假设公司需要处理不同金额的采购申请&#xff0c;不同级别的经理有不同的审批权限&#xff1a; // 抽象处理者&#xff1a;审批者 abstract class Approver {protected Approver successor; // 下一个处理者// 设置下一个处理者pub…...

编程新知 2025/10/16 22:41:12